Uncategorized

What do I need to install a cheap portable dishwasher under $200?

Is this the first time you’re trying to install a cheap portable dishwasher? Are you find it difficult to install a dishwasher? And don’t you want to call a professional that will charge a lot of cash? And you don’t know where to start and which tools and parts you use?

In this article, we’ll show you how to install a portable dishwasher step-by-step from a to z.

A portable dishwasher is just like its full-size built-in counterpart, only smaller, lighter, and more versatile. Since they are easy to set up and use, you’ll often be seeing this type of dishwasher in RVs, campsites, dorms, or apartments.

So please follow the steps and instructions and don’t skip any step because if you do that you’ll miss something and your dishwasher will not operate correctly.

What do I need to install a cheap portable dishwasher under $200?

Part supplied:

1. Faucet adapter kit included in Installation Package.

  • Faucet Adapter
  • Casters
  • Thin and thick washers

Tools you will need:

  • Pliers
  • Small Hammer
  • How to install a portable dishwasher step-by-step

    Step1. Unpacking your portable dishwasher

    Have at least two people move and install the dishwasher to prevent personal injuries. Remove all packaging materials: shipping tape, foam pieces, etc.

    before use.

    • Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners.
    • Check and make sure all parts necessary for installation are included.

    Step2. Positioning your portable dishwasher

    This cheap portable dishwasher is designed for countertop installation. The dishwasher is equipped with a water supply and drain hoses that can be positioned to the right or the left to facilitate proper installation.

    • Make sure the water supply/faucet connection is within reach of the inlet and drain hose assembly (5 ft).

    Step3. Electrical Requirements

    Make sure the electrical outlet is within reach of the power supply cord (4.5 ft).

    It is recommended to not use receptacles that can be turned on/off by a switch or pull chain. Refer to the rating label and be sure the voltage and frequency correspond to the power supply.

    If a mating wall receptacle is not available, it is the personal responsibility of the customer to have a properly grounded, 3-prong wall receptacle installed by a certified electrician.

    Step4. Install casters

    1.  Move the dishwasher close to its intended use and storage location.

    2. Place two shipping corner posts or other protective material behind them.

    3. Carefully lay the dishwasher over onto its side and rest it on the protective surface.

    4. Firmly push casters into holes as shown.

    NOTE: It may be helpful to place a piece of wood between the caster wheels and then lightly tap the wood with a hammer.

    If needed, place a block of wood between wheels and tap it on the seat.

    6. Carefully upright the dishwasher onto its casters.

    • Do not push down on an open door.

    Step5. Install faucet adapter

    The special faucet adapter supplied with your dishwasher must be attached to the sink faucet before you can use your dishwasher.

    The faucet adapter is designed to fit standard spouts having internal or external threads. You will find the adapter and two washers in the faucet adapter packet in your dishwasher.

    1. Attach the Faucet Adapter

    To install a faucet adapter, first, remove the old aerator or trim ring on your faucet spout.

    2. External Threads

    • If the faucet has external threads: Insert the thinner of the two washers into the faucet adapter and attach it to the faucet spout.

    • Tighten with pliers.

4. Non-Standard Threads

• If the faucet adapter threads do not match your faucet spout, your local hardware or plumbing supply store normally has additional fittings to adapt your faucet spout to the special faucet adapter. We suggest that you disconnect the sink spray attachment, if your sink has one, and place a cap over the opening.

Step6. Connect the uncouple to the faucet

1. Run a garbage disposer, if you have one, to clean out the disposer and thus allow water to drain from the sink through the disposer and down the drain.

2. Run a hot water faucet to purge cold water from the hot water line. The hot water must be between 120°F and 150°F for best wash performance. • Roll the dishwasher to a position just in front of the sink.

3. Pull the uncouple and its hoses completely out from the storage compartment at the rear of the dishwasher.

4. Attach the uncouple to the faucet adapter following the three steps below:

  • Depress the locking collar at the top of the uncoupled.
  • Place the uncouple completely over the faucet adapter.
  • Release the locking collar.

The uncouple should now be locked onto the faucet adapter.

• Turn on the hot water faucet and check for leaks. If a leak is detected, disconnect the uncouple, and refer to Step 4.

NOTE: The unicouple’s small hose carries water from the faucet to the dishwasher.

The large hose carries water from the dishwasher to the sink. Orient the faucet with the uncouple attached so water from the uncouple will run into the sink drain.

Step7. Faucet adapter leak

Skip this step if no uncouple leak was observed.

If a uncouple leak was observed in Step 3, take whatever actions are necessary to repair the leak. This may be as simple as tightening the faucet adapter.

Or, it may require the services of a plumber if water is leaking from the interface between the moveable faucet arm and the fixed part of the faucet fastened to the sink.

Step8. Pretest checklist

Review this list after connecting your dishwasher to avoid charges for a service call that is not covered by your warranty.

1. Open the door and remove all foam and paper packaging.

2. Locate the Owner’s Manual.

3. Read the Owner’s Manual to familiarize yourself with the operation of the dishwasher.

4. Remove the protective film, if present, from the control panel, door, and cabinet.

5. Add 2 quarts of water to the bottom of the dishwasher to lubricate the pump seal.

6. Plug the power cord into the outlet.

7. Close and latch the dishwasher door.

8. Start the dishwasher.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button